Journal cover Journal topic
Atmospheric Measurement Techniques An interactive open-access journal of the European Geosciences Union
Journal topic
AMT | Articles | Volume 12, issue 3
Atmos. Meas. Tech., 12, 1717–1737, 2019
https://doi.org/10.5194/amt-12-1717-2019
© Author(s) 2019. This work is distributed under
the Creative Commons Attribution 4.0 License.
Atmos. Meas. Tech., 12, 1717–1737, 2019
https://doi.org/10.5194/amt-12-1717-2019
© Author(s) 2019. This work is distributed under
the Creative Commons Attribution 4.0 License.

Research article 18 Mar 2019

Research article | 18 Mar 2019

Marine liquid cloud geometric thickness retrieved from OCO-2's oxygen A-band spectrometer

Marine liquid cloud geometric thickness retrieved from OCO-2's oxygen A-band spectrometer
Mark Richardson1,2, Jussi Leinonen1, Heather Q. Cronk3, James McDuffie1, Matthew D. Lebsock1, and Graeme L. Stephens1,4 Mark Richardson et al.
  • 1Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91125, USA
  • 2Joint Institute for Regional Earth System Science and Engineering, University of California Los Angeles, Los Angeles, CA 90095, USA
  • 3Cooperative Institute for Research in the Atmosphere, Colorado State University, Fort Collins, CO 80521, USA
  • 4Department of Meteorology, University of Reading, Reading, RG6 6BB, UK

Correspondence: Mark Richardson (markr@jpl.caltech.edu)

Abstract
Back to toptop

This paper introduces the OCO2CLD-LIDAR-AUX product, which uses the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) lidar and the Orbiting Carbon Observatory-2 (OCO-2) hyperspectral A-band spectrometer. CALIPSO provides a prior cloud top pressure (Ptop) for an OCO-2-based retrieval of cloud optical depth, Ptop and cloud geometric thickness expressed in hPa. Measurements are of single-layer liquid clouds over oceans from September 2014 to December 2016 when collocated data are available. Retrieval performance is best for solar zenith angles <45 and when the cloud phase classification, which also uses OCO-2's weak CO2 band, is more confident. The highest quality optical depth retrievals agree with those from the Moderate Resolution Imaging Spectroradiometer (MODIS) with discrepancies smaller than the MODIS-reported uncertainty. Retrieved thicknesses are consistent with a substantially subadiabatic structure over marine stratocumulus regions, in which extinction is weighted towards the cloud top. Cloud top pressure in these clouds shows a 4 hPa bias compared with CALIPSO which we attribute mainly to the assumed vertical structure of cloud extinction after showing little sensitivity to the presence of CALIPSO-identified aerosol layers or assumed cloud droplet effective radius. This is the first case of success in obtaining internal cloud structure from hyperspectral A-band measurements and exploits otherwise unused OCO-2 data. This retrieval approach should provide additional constraints on satellite-based estimates of cloud droplet number concentration from visible imagery, which rely on parameterization of the cloud thickness.

1 Introduction
Back to toptop

The Orbiting Carbon Observatory-2's (OCO-2) primary mission is to retrieve atmospheric CO2 concentration (XCO2) using reflected sunlight (Crisp, 2015; Crisp et al., 2004; Eldering et al., 2017). This requires measurements at high spatial and spectral resolution with excellent signal-to-noise ratio, and OCO-2 measures spectra not just in the weak and strong CO2 bands but also in the molecular oxygen (O2) A band near λ=0.78µm. The XCO2 retrieval is designed for clear skies and the A band helps to identify and exclude cloudy scenes, and as of December 2016, between 88 % and 93 % of soundings were not used (Crisp et al., 2017). These soundings are rich in cloud information (Richardson and Stephens, 2018) and here we present the OCO2CLD-LIDAR-AUX product, which exploits these unused OCO-2 data in concert with collocated measurements from the Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) on the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) satellite.

For single-layer marine clouds we retrieve cloud optical depth (τ), cloud top pressure (Ptop) and the geometric thickness (H) but express this H in terms of cloud pressure thickness in hPa (ΔPc). ΔPc is poorly constrained by other satellite products. For example, current spaceborne radar has insufficient sensitivity and range resolution to estimate the thickness of thin clouds, while lidar is readily attenuated before reaching the cloud base in even moderately optically thick clouds. The cloud thickness has a first-order relationship to liquid water path (LWP) and mixing between the boundary layer and free atmosphere (Boers and Mitchell, 1994). Satellite estimates of the cloud droplet number density make assumptions about cloud vertical structure that parameterize the cloud geometrical thickness (see, e.g. Grosvenor et al., 2018 for a recent summary). Realistic representation of the cloud droplet number is central to accurate representation of aerosol indirect effects in models (Jones et al., 1994; Lohmann and Feichter, 2005). Marine boundary layer clouds tend to have high albedo and warm tops, making them effective radiative coolers, and their response to current human-forced climate change is a major uncertainty in the amount of global warming that will occur (Bony and Dufresne, 2005). Improved observational constraints on their properties will help modellers to improve the fidelity of their simulations and reduce uncertainty in projected climate change.

The ocean stratocumulus decks are a major contributor to low cloud radiative effects. One model study suggests that a global cooling of -8.0±0.1 W m−2 could be achieved primarily by brightening these clouds through increasing cloud condensation nuclei (Latham et al., 2008). This is approximately the heating that would result from a quadrupling of atmospheric CO2, and such large potential radiative changes make understanding their processes very desirable. They tend to form where cool ocean water upwells near the western coasts of continents, particularly near California, Peru, Namibia and Australia. Unlike many other convective clouds, they are driven by cooling at the cloud top rather than warming from the surface, and a detailed summary of the processes involved can be found in Wood (2012).

The OCO2CLD-LIDAR-AUX product provides new information about low marine clouds, both for the OCO-2 native footprints and collocated with CloudSat, allowing quick comparison with CloudSat radar and CALIPSO lidar cloud products. OCO2CLD-LIDAR-AUX is an iterative optimal estimation retrieval that uses a radiative transfer model to best fit a set of cloud properties to the observed spectrum. This paper describes the retrieval algorithm, data sources and modelling techniques, describes and validates outputs against other satellite products and summarizes and maps the retrieved cloud properties. It is organized as follows: Sect. 2 discusses the structure of the targeted clouds and the history and principle of their retrieval, Sect. 3 describes the OCO-2 mission, instrumentation and orbit, Sect. 4 describes the retrieval, Sect. 5 explores the data with comparison to its priors, MODIS and CALIPSO, Sect. 6 reports and maps the full dataset retrieval statistics and Sect. 7 concludes.

2 Marine boundary layer clouds and retrieval of their geometric thickness
Back to toptop

2.1 The subadiabatic cloud model

A common assumption for marine boundary layer clouds is that they follow an adiabatic or subadiabatic vertical profile, and clouds matching these assumptions have been observed in aircraft campaigns such as those partaking in the Aerosol Characterization Experiment-2 (Pawlowska and Brenguier, 2000; Raes et al., 2000), and the predicted relationships between properties such as geometric thickness and liquid water path have also been measured (Painemal et al., 2017; Zuidema et al., 2012).

In this model, droplets in an air parcel are activated at the lifting condensation level (LCL), and as the parcel drifts upward, excess vapour condenses onto the droplets. In adiabatic conditions, liquid water content (LWC) is equivalent to the difference between the local saturation vapour pressure es(z) and the saturation vapour pressure at the LCL. For the temperatures, pressures and relatively short altitude ranges of these clouds, this is well modelled by a linear LWC increase with height at a rate determined by the adiabatic condensation coefficient cw. This is sometimes labelled Γw and referred to as a lapse rate.

Non-adiabatic processes such as drizzle or entrainment of free tropospheric air at the cloud top can change these profiles, resulting in subadiabatic conditions which can be parameterized (Betts, 1985; Boers and Mitchell, 1994). A set of assumptions is now commonly used, including constant cloud average values for subadiabiticity and the ratio between volume mean and effective droplet radius (e.g. Szczodrak et al., 2001). Grosvenor et al. (2018) summarize many of the key relationships in a review of droplet number density, Nd, and derivations relevant for this study are in Sect. S1 in the Supplement.

In the subadiabatic model, geometric thickness is related to cloud top effective radius re,ad,t and cloud optical depth τc as

(1)H=20ρwre,ad,tτ9Qextcwfad,

where ρw is the density of water, Qext is the extinction efficiency (Qext≈2 for water droplets in the A band) and fad=1 in adiabatic conditions and decreases with increasing subadiabaticity. We use this equation to derive the prior H in OCO2CLD-LIDAR-AUX.

While real marine clouds in stable boundary layers can be well modelled by a subadiabatic structure, it is common for cloudy radiative transfer to assume plane-parallel clouds that are both horizontally and vertically homogeneous. For a fixed LWP and H, a vertically homogeneous cloud has the same optical depth as a subadiabatic cloud provided that

(2)re,h=56re,ad,t,

where re, h is the homogeneous cloud effective radius, and this was derived and tested using cloud structures discretized at 25 m in the vertical in Brenguier et al. (2000). We use this argument to justify the combination of a subadiabatic cloud structure to derive prior H with the use of a vertically homogeneous cloud structure in the retrieval.

However, we highlight that a number of assumptions are used in these derivations. The fad in Eq. (1) is assumed to be constant with height, but another important factor is the ratio

(3)k=rv3re3.

This relates the volume mean equivalent radius rv to the effective radius relevant for radiative transfer calculations. It is related to the width of the droplet size distribution, and in situ observations place k around 0.80 (Martin et al., 1994; Pawlowska and Brenguier, 2000) in marine clouds. Although it has also been observed to vary with height (Painemal and Zuidema, 2011), our derivations assume it to be constant.

Relationships derived from the subadiabatic cloud model can be used to retrieve Nd and H from MODIS τ and effective droplet radius (re, M). Simulations by Platnick (2000) suggest that the retrieved re, M is smaller than re,ad,t as the channel weighting functions are below the cloud top but that the ratio depends on the MODIS channel used, re profile and somewhat on the cloud optical depth. If the MODIS retrieval performs similarly to those simulations, then re, M is similar to re, h according to the results in Platnick (2000) Table 3a. The subadiabatic model also provides a simple relationship between LWP and H:

(4)LWP=12fadcwH2,

allowing any LWP product to be converted into a subadiabatic cloud thickness. However, aircraft measurements show a wide range of values for the assumed parameters, such as those related to mixing (Wood, 2005), which can bias MODIS retrievals (Painemal and Zuidema, 2011).

A term-by-term error analysis estimated H could be estimated from space to within ±20 % (Bennartz, 2007), but validation is challenging due to the difficulty of retrieving H of these clouds. Active instruments can profile many cloud types, and H has been obtained from surface-based lidar and radar measurements as part of the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) programme, as first demonstrated in Dong et al. (1997). Ceilometers alone allow high precision determination of the cloud base (Dong et al., 2002), which could be combined with the CALIPSO cloud top to provide H. A long-term oceanic ARM site is located on the Azores (the Eastern North Atlantic, ENA, site), and a site was also on Ascension Island from June 2016 to October 2017.

Greater geographic coverage has been obtained over the oceans through ship-based measurements such as the Marine ARM GPCI Investigation of Clouds (MAGIC) experiment, which included measurements taken from ships between Los Angeles, California and Hawaii. In principle, H can be also be obtained from cloud radar mounted on aircraft that are commonly used in airborne campaigns (Wood et al., 2011; Zuidema et al., 2016).

Unfortunately, these instruments are not widely deployed and there is no consistent large-scale, continuous record of marine cloud thicknesses available from surface or airborne measurements. We cannot use the Azores or Ascension Island ARM datasets for validation because no OCO2CLD-LIDAR-AUX retrieval occurs within ±0.5 (70–80 km) of their locations, and we cannot use MAGIC retrievals of the cloud base in concert with CALIPSO since the ship measurements finished before the launch of OCO-2. Future coverage may be improved through the development of more compact and efficient ceilometers that could be widely attached to buoys as in Mariage et al. (2017) or on seafaring autonomous vehicles (Meinig et al., 2015).

Spaceborne sensors offer unsurpassed coverage of ocean clouds, but current spaceborne capabilities to retrieve H of marine boundary layer clouds are limited since these clouds are often optically thick enough to attenuate lidar, and with H from 102 to 103 m, radars need higher vertical sampling than that offered by, for example, CloudSat's downsampled 240 m bins.

Lidar can, however, be used to estimate the cloud top droplet number density for clouds with narrow droplet size distributions. This has been demonstrated using retrievals based on combined measurements from CALIPSO and the Polarization and Directionality of the Earth Reflectance (POLDER) instrument (Zeng et al., 2014). This can be related to H when combined with the same assumptions used in MODIS retrievals.

2.2 Explicit retrieval of cloud thickness using photon path length

An alternative approach to retrieve cloud thickness is to consider measurements which are sensitive to photon path length through differential absorption between channels. The basic principle of these retrievals is that if an instrument measures channels with similar wavelengths but different molecular absorption coefficients, then in the absence of atmospheric emission or scattering into the beam their radiances will both be described by Beer's law:

(5)I=I0exp(-kΔz),

where I is the measured radiance, I0 the initial radiance, k the extinction coefficient and Δz the photon path length. In the case of reflectance measurements such as those from OCO-2, the narrow wavelength range tends to mean that I0 and Δz are similar between channels, and therefore from measurements of I and spectroscopic information for k, the photon path length can be derived. In a uniform cloud scene of sufficient optical depth, the photon path will consist of an above-cloud path that changes with Ptop and a within-cloud path that depends on the within-cloud scattering, which is in turn related to H and τ.

The use of photon path length information for cloud top pressure retrievals was suggested as early as the 1960s (Hanel, 1961; Yamamoto and Wark, 1961), and in more recent decades the possibility of probing within-cloud structure has been developed (Li and Min, 2010; Min et al., 2004).

The oxygen A band on OCO-2 is a good candidate for this sort of measurement, as it relies on absorption by a ubiquitous and well mixed atmospheric constituent whose fractional abundance does not greatly vary in space or time. From a single measurement using two channels, only a single piece of information on the photon path can be obtained, and this is related to the total photon path. However, by combining multiple angles, channels or bands it has been proposed that obtaining both Ptop and H is possible. Suggestions have included multi-angle measurements such as in Merlin et al. (2016) or both the A and B band as in Yang et al. (2013).

For the purpose of marine stratocumulus, however, neither of these approaches have proven to be tenable. The multi-angular results in Merlin et al. (2016) refer to clouds with H>2–3 km, and an updated information content analysis accounting for the on-orbit performance of the A- and B-band sensors of the Earth Polychromatic Imaging Camera (EPIC) on the Deep Space Climate ObserVatoRy (DSCOVR) has concluded that “only cloud top height can be reliably inferred” (Davis et al., 2018).

There is also a heritage of considering high spectral resolution measurements in the oxygen A band to obtain H. Early work considered cloud top height (Fischer and Grassl, 1991; Yamamoto and Wark, 1961) and later estimated the required spectral resolution required to allow separation of the above- and within-cloud components to allow retrievals of both Ptop and H (Heidinger and Stephens, 2000; O'Brien and Mitchell, 1992; Stephens and Heidinger, 2000). These suggested that a spectral sampling of 0.5–1.0 cm−1 is necessary for a joint retrieval, similar to the 0.5 cm−1 that Min and Harrison (2004) estimated as necessary to obtain four pieces of information in an atmosphere with optically thin scattering layers. These results are dependent somewhat on other instrument characteristics such as the signal-to-noise ratio. Channels with stronger absorption tend to be more sensitive to Ptop and those with weaker absorption to H, since the more strongly absorbing channels tend to see complete extinction if their photons are multiply scattered within the cloud. Higher spectral resolution means channels with thinner spectral width that cover a smaller range of absorption coefficients, and this improves sampling in terms of oxygen absorption coefficient so aids in distinguishing between Ptop and H contributions.

However, spectral resolution is not the only limiting factor: instrumental noise and other uncertainties such as those associated with the vertical profile of atmospheric moisture above the cloud can also limit a retrieval. Information content analyses have shown theoretical differences in performance between the Global Ozone Monitoring Experiment-2 (GOME-2, Munro et al., 2016) and OCO-2 instruments. GOME-2 has spectral sampling of approximately Δλ=0.21 nm and a full width at half maximum (FWHM) near 0.50 nm, compared with OCO-2's Δλ≈0.02 nm and FWHM ≈0.04 nm (approximate values; they vary with wavelength due to instrumental design). GOME-2's typical signal-to-noise ratio (SNR) is near 100, whereas OCO-2's continuum channel SNR typically ranges from 400 to 800 in the A band, although it is larger in absorption bands.

Considering only instrumental SNR, it was found that GOME-2 is not able to retrieve H in addition to Ptop (Schuessler et al., 2014); however OCO-2 is able to retrieve both for horizontally homogeneous clouds even after accounting for error covariance terms due to uncertainty in re, h and the temperature and humidity profiles (Richardson and Stephens, 2018). This analysis determined that a micro-window of 75 OCO-2 channels contained sufficient information for a three-property joint cloud retrieval.

Example simulated cloudy scene spectra for GOME-2 and OCO-2 are shown in Fig. 1, and the 75 channels used in OCO2CLD-LIDAR-AUX are highlighted in red. Also displayed are responses for each instrument and cloud property, sorted by the channel-mean oxygen absorption coefficient in order to emphasize how spectral response depends on this.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f01

Figure 1(a) Simulated A-band reflectance spectrum for a vertically homogeneous cloud with τ=10, re,h=12µm and Ptop=750 hPa as seen by OCO-2 and GOME-2-like sampling. The red OCO-2 subset refers to the 75 channels used in OCO2CLD-LIDAR-AUX. (b) OCO-2 and GOME-2 cloud τ Jacobians with channels organized by the baseline spectrum's channel mean molecular oxygen ln(τO2). (c) IIc Jacobians in response to Ptop. (d) IIc Jacobians in response to ΔPc.

Download

The cloud optical depth Jacobian is shown as I/τ, where I refers to each channel's modelled radiance. H is expressed as ΔPc, in terms of atmospheric pressure coordinates in hPa. The Ptop and ΔPc Jacobians are shown as the response in IIc, where Ic is the continuum radiance.

Inspection of Fig. 1b–d shows similar responses to optical depth across the two instruments but a clear difference for the Ptop and ΔPc responses. In particular, the GOME-2 Jacobians are more similar to each other than those of OCO-2. For OCO-2 the greatest change in fractional absorption, represented by the deepest trough in the IIc Jacobian, occurs in more strongly absorbing channels for Ptop compared with ΔPc, as described previously. It is this difference in Jacobians that results in independent information that allows retrievals of both Ptop and H with OCO-2.

3 OCO-2 mission, instrumentation and orbit
Back to toptop

We summarize relevant details of the OCO-2 orbit, viewing modes and instrumentation here; full descriptions are in the Level 2 Full Physics Algorithm Theoretical Basis Document (L2FP ATBD; Boesch et al., 2017).

OCO-2 leads the A-train constellation (L'Ecuyer and Jiang, 2010), and over the OCO2CLD-LIDAR-AUX coverage from 6 September 2014 to 30 December 2016, it followed the CloudSat reference ground track (RTG) approximately 7 min ahead of CALIPSO and approximately 217 km to the east of the Aqua RTG in the ascending node. The A-train is in a Sun-synchronous orbit with an ascending equatorial crossing time near 13:30 and an equatorial repeat time of approximately 16 days.

The OCO-2 operational science viewing modes are nadir and glint, with glint preferred for ocean XCO2 retrievals due to improved SNR. Nadir, however, offers the advantages of collocation with the near-nadir CloudSat and CALIPSO views, plus a shorter path through the atmosphere which allows more signal from absorbing channels.

Originally orbits were alternated between nadir and glint view before some ocean-dominated orbits were always committed to glint. OCO2CLD-LIDAR-AUX only uses nadir orbits when collocation with CALIOP is possible.

The satellite operates in an angled push broom fashion with an eight-footprint swath whose orientation rotates through the orbit to optimize solar panel output. Footprint geometry varies but at nadir is approximately 1.4 km ×2.2 km. Each footprint is measured by three co-boresighted Fourier transform grating spectrometers in the O2 A band, weak CO2 band (λ∼1.61µm) and strong CO2 (λ∼2.06µm) band. Spectral sampling varies from 0.01 to 0.02 nm in wavelength, and instrument line shape full width at half maximum (ILS FWHM) is approximately 0.04 nm. A-band signal-to-noise ratio (SNR) typically ranges from 400 to 800 in continuum channels.

4 Retrieval design and data sources
Back to toptop

OCO2CLD-LIDAR-AUX uses an iterative optimal estimation scheme in which a prior cloud state is updated such that the simulated radiances associated with that state agree with the measured OCO-2 spectrum, given appropriate weighting to uncertainties in both the prior and observations.

4.1 Optimal estimation principles

For each footprint for which a retrieval is attempted we construct a cloud state vector x=lnτ,lnPtop,lnΔPcT and an observation state vector y=I1,I2,,I75T, where each Ii (i=1,  ,75) is a measured channel radiance. ΔPc is the cloud geometric thickness H expressed in terms of change in atmospheric pressure. We begin with a prior cloud state vector whose components are Gaussian, represented by a mean state vector xa and covariance matrix Sa. Meanwhile the observational uncertainty is represented by a zero-mean Gaussian with covariance matrix Sϵ. Optimal estimation produces a maximized posterior probability density of the posterior state given both the prior state and the observations, with appropriate weighting for their relative uncertainties. In our case the individual contributions to observational uncertainties are assumed to be independent and thus add in quadrature such that Sϵ is simply the sum of each term's covariance. The posterior is estimated by applying Bayes' theorem, assuming a locally linear forward model encapsulated in the Jacobian matrix K whose elements are Ki,j=yi/xj. The solutions for the posterior state and its covariance in a totally linear case are (Rodgers, 2000)

(6)x^=xa+SaKTKSaKT+Sϵ-1y-Kxa(7)S^=KTSϵ-1K+Sa-1-1.

Non-linearity is addressed by allowing multiple iterations, where step n+1 properties are related to the prior step n via

xn+1=xa+SaKnTKnSaKnT+Sϵ-1(8)y-Fxn+Kn(xn-xa),

where F is the forward model. Table 1 lists the sources for each element of these matrices: prior τ uses a lookup table based on A-band radiances, and the Ptop is derived from CALIPSO and ΔPc from Eq. (1) with the prior τ and assumed re,h=12µm.

Table 1Construction of each input vector or matrix in retrieval.

Download Print Version | Download XLSX

The retrieval takes the first step equal to the prior, i.e. x0=xa, and then iterates up to six times using the posterior of the previous step as the starting point of the next iteration. The step with the lowest χ2 is reported as the retrieved state, and the number of iterations was selected to balance quality of convergence and computational expense. No explicit convergence criterion was adopted: all retrievals that did not trigger computational problems are reported and users are provided with both the state estimate and the χ2 for the retrieval step used. Synthetic retrieval tests showed typical convergence with two steps (Richardson and Stephens, 2018), and 58 % of successful retrievals used step 1 or 2. Only around 10 % of retrievals selected step 6.

4.2 Forward model

We use the OCO-2 Level 2 Full Physics retrieval algorithm's radiative transfer model (henceforth L2RTM). This is a multiply scattering line-by-line radiative transfer model based on VLIDORT (Spurr, 2006) with a modified 2 orders of scattering code (2OS; Natraj and Spurr, 2007) and is available from GitHub (https://github.com/nasa/RtRetrievalFramework, last access: 7 March 2019). It was designed for clear skies but has previously been modified for cloudy scene simulations (Richardson et al., 2017).

Clouds are treated as homogeneous plane-parallel layers and scattering properties are from Mie scattering calculations using a gamma distribution with characteristic re=re,h=12µm (see Sect. 5.3.3 for discussion on sensitivity to this choice). This selection is based on the median MODIS droplet size retrieved using the 2.1 µm channel for our selected cloud cases (Nakajima and King, 1990). The median MODIS re, M is 12.5 µm with a 14 %–86 % range of 8.4–18.6 µm; we use the closest integer value since precalculated Mie tables are available only for integer re values in the L2FP code.

It has been shown that for typical cloud retrieval channels, vertically homogeneous clouds have similar radiative properties to subadiabatic clouds of the same H, LWP and τ provided that their re, h is 5∕6 that of the subadiabatic cloud top re,ad,t (Brenguier et al., 2000). As discussed in Sect. 2.1 the retrieved re, M is sensitive to within-cloud rather than cloud top re (Platnick, 2000), except when non-adiabatic influences such as entrainment of dry air and evaporation reduce cloud top re (Nakajima et al., 2010). Since the appropriate re, h is 5∕6 of re,ad,t, and these MODIS retrievals sample within the cloud where droplets are smaller, we expect re, M to approach re, h. Regardless, we test the sensitivity of the retrieval to re, h in Sect. 5.3.3.

A fixed re, h was selected to speed up computation: the L2RTM requires a full extinction profile for every sounding and every re, h used for any sounding in the orbit. Limiting this to one option speeds up the retrieval, and its effect on the retrieval is included by adding a term to the observation covariance (Richardson and Stephens, 2018).

Table 2Product names, version numbers and citations for key inputs and the forward model used in OCO2CLD-LIDAR-AUX.

Download Print Version | Download XLSX

Pressure levels are assigned to the cloud top, centre and bottom, and 17 other layers are linearly interpolated to the top of atmosphere or surface. An extinction coefficient is assigned to the cloud centre and interpolated uniformly between the cloud top and bottom. Jacobians are calculated numerically using finite differences as follows: (1) for τ, the extinction is scaled, (2) for Ptop, all three cloud pressure levels have their pressure increased by δP and (3) for ΔPc, the bottom level pressure is increased by δP and the centre level by 0.5δP, and the extinction is scaled to maintain constant τ. The size of each increment is in Table 1.

The L2RTM also requires information about location, geometry, meteorology, satellite orbital parameters and instrument characteristics. For this we use the OCO-2 files associated with Version 7 of the XCO2 product, since OCO2CLD-LIDAR-AUX processing began before the version 8 release. We use Level 1b science spectra (L1bSc) and interpolated weather forecasts from the European Centre for Medium-range Weather Forecasts (ECMWF), which provides temperature and humidity profiles along with surface wind speed for the Cox–Munk sea surface reflectance model (Cox and Munk, 1954). For O2 absorption we use the OCO-2 version 5 absorption coefficient (ABSCO) tables (Drouin et al., 2016) which were used in version 8 of the OCO-2 XCO2 retrieval. They better represent oxygen absorption in several ways compared with those used in version 7, including through the handling of line mixing and collision-induced absorption. Input properties used, version numbers and key citations are provided in Table 2.

4.3 Algorithm design

The algorithm first attempts to identify liquid clouds over the ocean, then assigns a prior and iterates to a posterior state using Eq. (6). OCO-2's original cloud screening algorithm was not designed for nadir view over the oceans. Given that non-cloudy scenes are dark in nadir view, we collect A-band and weak CO2 continuum radiances Ic from the L1bSc spectra and divide by μ0=cos(SZA), where SZA is the solar zenith angle. Then the 10 channels that were, on average, brightest over November 2015 are taken as the continuum, with a separate set for each footprint across the swath. If μ0-1I exceeds a threshold in each channel (A-band μ0IO2=6×1019, weak CO2 band μ0Iwk 1×1019 photons m−2 s−1 sr−1µm−1), then a cloud is flagged and agreement with the MODIS “confident” cloud flag is approximately 85 %. This threshold is equivalent to just over 15 W m−2 sr−1µm−1, compared with the median μ0-1I near 4 W m−2 sr−1µm−1 in clear-sky conditions, according to the OCO-2 A-band preprocessor.

A further constraint is provided by CALIPSO: the nearest CALIPSO footprint is checked, and the footprint is only used if CALIPSO identifies a single-layer cloud whose Ptop>680 hPa. The CALIPSO Ptop threshold limits our sample to the low cloud threshold of the International Satellite Cloud Climatology Project (Rossow and Schiffer, 1991) and helps to filter out non-liquid clouds. CALIPSO also helps to exclude some multi-layer cloud cases which violate our retrieval assumption of a single-layer cloud.

If both of these tests agree on a cloud, then the continuum A-band and weak CO2μ0I are used to estimate cloud phase via a lookup table that exploits how ice absorbs more strongly than water in the weak CO2 band relative to the A band (Nakajima and King, 1990). A lookup table is also used to estimate the prior cloud optical depth from the continuum A-band radiance, since more optically thick clouds tend to be brighter, and Fig. 2 shows both the phase and τ lookup tables. Other prior properties and covariance terms are assigned as described in Table 1. For observation covariance, the footprint SNR is added to precalculated matrices that are scaled for μ0 and cloud τ as described in Richardson and Stephens (2018). These matrices include terms related to uncertainty in atmospheric temperature and moisture, plus cloud re, h. Figure 3 is a flow diagram that summarizes the full retrieval.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f02

Figure 2Lookup tables for cloud phase and prior cloud τ. Cloud phase is coloured for regions of SZA-corrected continuum A-band and weak CO2 band radiances. Cloud τ is shown on the right axis and is only a function of the A-band radiances.

Download

4.4 Product output fields and collocation with CloudSat

OCO2CLD-LIDAR-AUX is both a demonstration of hyperspectral A-band cloud retrievals and an attempt to fill in a gap in information about marine boundary layer clouds. It aims to allow this new information to be easily linked to CloudSat, CALIPSO and other mission data for cloud process studies.

The output files are therefore reported following the standard CloudSat granule structure as part of the Release 5 (R05) data products available from the CloudSat Data Processing Center (http://www.cloudsat.cira.colostate.edu, last access: 6 March 2019) along with an Interface Control Document that details all of the data structures.

The retrieved cloud properties τ, Ptop and ΔPc are collocated with the CloudSat footprints by minimizing surface distance between the centre of each instrument's footprint according to a nearest neighbour great circle scheme. Collocation introduces some inconsistencies which we refer to as “collocation error”. For OCO-2 and CloudSat, differences in overpass times and footprint shape and size are the main factors, but for validation against MODIS, additional contributions may occur due to the different viewing geometries causing parallax error.

Table 3Components of Quality_flag. If a retrieval is summed, then the final Quality_flag is the sum of all of these Quality_flag values.

Download Print Version | Download XLSX

Cloud retrievals are provided for a CloudSat footprint whenever the distance between the footprint centres is <1.25 km, or approximately half the length of an OCO-2 or CloudSat footprint. Since OCO-2 has a swath of eight footprints and CloudSat does not, most of the OCO-2 data are not matched to CloudSat. Therefore the native OCO-2 footprint structure is also reported, and these are distinguished by the inclusion of full_swath in the dataset name. For example, the dataset Cloud_Optical_Depth is the OCO-2 estimate of τ collocated with CloudSat, whereas full_swath_Cloud_Optical_Depth is the OCO-2 that includes all OCO-2 footprints. Furthermore, contextual information such as the solar zenith angle and the local variance of the A-band continuum radiance is provided, along with collocation indexing and matchup distances. This allows users to include more swath information or apply their selected matchup criteria.

Finally, a Quality_flag is provided whose components are described in Table 3. When a retrieval is attempted, the Quality_flag is initialized to zero, and integer values are added as potential warning factors are identified such that Quality_flag =0 represents the best quality data. The final value is the sum of all flags associated with the retrieval, and valid retrievals have a flag range of 0–7. It is recommended that any cases with Quality_flag ≥4 are also excluded, as this includes the very small fraction of soundings in which the detector experienced a cosmic ray strike, resulting in non-physical spectral signatures. The retrieval statistics are split by Quality_flag and analysed in Sect. 5, which aims to provide the evidence that users need to decide which range of Quality_flag values they can accept.

4.5 Algorithm throughput and performance statistics

The average number of attempted retrievals with a <10 km matchup distance to CALIPSO is 7336 per orbit (∼11 % of OCO-2 footprints). Table 4 shows statistics of the retrieval throughput and some comparisons to MODIS, which we use later for validation.

Table 4Statistics of a test sample of OCO2CLD-LIDAR output.

Download Print Version | Download XLSX

Retrieval failure occurs in 2.0 % of cases and includes incomplete or inconsistent input data and failures in the radiative transfer or optimal estimation retrieval code. 0.1 % are rejected due to cosmic ray strikes detected in our channels, and 4.6 % are outside the retrieval space, mostly in a posterior state with a cloud bottom below Earth's surface. Also shown in Table 4 is that 84.5 % of OCO2CLD-LIDAR-AUX successful retrievals are identified as liquid clouds by MODIS, and 71.0 % have collocated MODIS optical depth retrievals. This subset is used for validation in Sect. 5.

The retrieval is computationally intensive and the cloud retrieval is not integrated into the OCO-2 L2FP clear-sky XCO2 retrieval. Major bottlenecks include (1) reading and writing data necessary to link the L2FP radiative transfer code to the cloud retrieval and (2) the optimal estimation retrieval that includes inverting multiple 75 element × 75 element matrices. The average orbit processing time is approximately 1 h, and this is helped by the sub-selection of 75 channels from the 853 undamaged A-band channels that reduces the theoretical computational burden of the matrix calculations by around 99 %. Using the full spectrum in the retrieval results in an average computation time of >30 h per orbit.

5 Cloud properties from OCO2CLD-LIDAR-AUX compared with MODIS and CALIPSO
Back to toptop

5.1 Optical depth compared with MODIS

Cloud retrievals are best suited for single-layer, horizontally homogeneous clouds, with a low solar zenith angle. OCO2CLD-LIDAR-AUX's Quality_flag is designed to help users identify these cases. Firstly, the solar zenith angle can bias MODIS-retrieved τ for reasons including angle-dependent differences in real-world radiative transfer including 3-D cloud effects and the plane-parallel assumptions commonly used in retrievals. These and others are discussed in the literature (Chambers et al., 2001; Grosvenor and Wood, 2014; Liang et al., 2015; Várnai and Marshak, 2002), and contribute to larger expected uncertainty in retrieved τ at higher solar zenith angles. The OCO2CLD-LIDAR-AUX Quality_flag increases the value of Quality_flag by 1 when the SZA >45.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f03

Figure 3Flow diagram illustrating the OCO2CLD-LIDAR-AUX retrieval.

Download

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f04

Figure 4OCO-2 minus MODIS τ statistics; in all cases the legend reports the median [14th, 86th percentiles]. (a) All retrievals absolute differences. (b) As (a) but each difference is divided by the matching MODIS uncertainty. (c) Retrievals split by SZA and radiance ratio warning flag. (d)As (c) but divided by MODIS uncertainties as in (b). These separations are part of the OCO2CLD-LIDAR-AUX Quality_flag: SZA above 45 adds 1 to Quality_flag, and Iwk/IO2 above 0.28 adds 2.

Download

Secondly, the ratio of the 10 channel continuum radiances in each band, Iwk/IO2, is related both to cloud droplet size and cloud phase. Particularly when ice is present, there is increased absorption of weak CO2 band radiance and therefore a lower ratio. While OCO2CLD-LIDAR-AUX estimates phase using the lookup table from Fig. 2, this was optimized based on agreement with MODIS for a subset of orbits. We find that this is not strict enough, and approximately 10 % of the data with Iwk/IO2<0.28 show much greater discrepancies compared with MODIS and CALIPSO. This is likely because the cloud is not entirely liquid or due to the presence of overlying cirrus or aerosol layers, and therefore a retrieval that attempts to fit a liquid cloud model to the observed spectrum will result in biased cloud properties. For these cases we increase the Quality_flag value by 2.

We compare the statistics of OCO-2 minus MODIS τ retrievals in Fig. 4 for the full sample (a, b) and subsets split according to their SZA and radiance ratio (c, d). Only footprints with valid OCO-2 and MODIS retrievals are included. Statistics are presented both for the absolute difference, δτ=τOCO-2-τMODIS, and scaled by the MODIS reported optical depth uncertainty, δτ/στ,MODIS. The distributions are non-Gaussian (full sample Kolmogorov–Smirnov test statistic =0.279, N>1.6×107, p<0.001) and skewed, so we report the median and the 14th–86th percentiles in place of the mean and standard deviation. For the full sample in Fig. 4b, the median bias is 0.02 times the MODIS uncertainty, and the 14 %–86 % range is −1.12 to 1.02. If collocation error were zero and errors between OCO-2 and MODIS were equal and independent, adding them in quadrature would result in an expected range of −1.41 to 1.41. The smaller differences we find indicate that MODIS and OCO-2 errors may be correlated and that the OCO-2 and/or MODIS uncertainties may be smaller than reported in the MODIS product.

For Quality_flag =0, where SZA <45 and Iwk/IO2<0.28, Fig. 4d shows that the median bias relative to MODIS is 4 % of the MODIS reported error, which is slightly larger than the full-sample bias. However, the 14 %–86 % range is narrower at −87 % to +83 %. The OCO-2 derived optical depths are consistent with those from MODIS.

5.2 Cloud top pressure versus CALIPSO, geometric thickness versus MODIS and implied subadiabaticity

Next we investigate the retrieved Ptop and ΔPc in Fig. 5. The retrieved values are compared with their priors, which for Ptop means a comparison with CALIPSO and for ΔPc a comparison with an adiabatic estimate based on the cloud's optical depth and an assumed 12 micron droplet size. As in the MODIS comparison, statistics are shown for the full dataset and for when it is subset by solar zenith angle and the Iwk/IO2 radiance ratio.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f05

Figure 5Posterior minus prior retrieval statistics; all legends report median [14th, 86th percentiles]. (a) All OCO-2 minus CALIPSO cloud top pressure. (b) All OCO-2 posterior minus prior cloud pressure thicknesses. (c) As (a) but subset by Quality_flag. (d) As (b) but subset by Quality_flag.

Download

The full sample distribution, particularly of Ptop, is skewed and its apparently small median bias of 4 hPa is large relative to the assumed 5 hPa prior error in Ptop. The median change in cloud pressure thickness is close to 0 hPa, so retrieved average cloud thickness matches the typical adiabatic cloud thickness.

When selecting Quality_flag =0, the ΔPc retrieval differences become more symmetric, with an 18 %–86 % range of [−5, 4] hPa. However, the retrieved Ptop bias is opposite to that of the full sample and shows that the OCO-2 retrievals result in increased cloud altitude relative to that seen by the precise CALIOP lidar. Our use of a tight prior constraint does ensure that the discrepancy is smaller than for MODIS minus CALIOP, of −22 [−115, 57] hPa, but this nevertheless needs investigation.

Comparison of ΔPc with an adiabatic prior is somewhat unsatisfying, given that we have no direct validation data to determine whether the OCO2CLD-LIDAR-AUX retrievals add extra value. Therefore we take an indirect approach based on comparison with MODIS cloud thickness. For this part we turn to geometric thickness H in metres, converting our ΔPc to H using a standard scale height calculation (e.g. Eq. 6 in Wood and Bretherton, 2006) and then convert MODIS-retrieved LWP to H using Eq. (4) with the local condensation coefficient calculated for the OCO-2 cloud base height using the collocated ECMWF meteorology and taking MODIS fad=1, since this is currently not retrieved. Here we temporarily switch to using H rather than ΔPc because (i) the ΔPc conversion would include using MODIS-derived Ptop, which could introduce greater spread, and (ii) we can relate H directly to the cloud adiabatic fraction fad for more insight into our retrieval's behaviour.

Following this, we have independent estimates for all three properties of our state vector, and 2-D histograms of these comparisons are shown in Fig. 6. Focussing on Fig. 6c, the OCO-2-based H tends to be larger than that from MODIS, implying a less adiabatic (i.e. lower fad) cloud.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f06

Figure 62-D histograms of (a) MODIS versus OCO-2 cloud τ, (b) CALIPSO versus OCO-2 Ptop and (c) MODIS versus OCO-2 H, with MODIS H being equivalent thickness based on retrieved liquid water path combined with Eq. (4) and fad=1. Bins with N<500 are masked, and only OCO2CLD-LIDAR-AUX Quality_flag =0 retrievals are shown.

Download

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f07

Figure 7Estimated adiabatic fraction of OCO-2 Quality_flag =0 retrieved clouds relative to MODIS, assuming equal liquid water paths and binned by estimated inversion strength. The first bin includes all cases where EIS <0C, and the last bin includes all cases where EIS >16C. (a) Posterior fad split by cloud τ. (b) The change in OCO-2 fad as posterior minus prior.

Download

One process that can reduce fad is entrainment of dry air at the cloud top, which effectively dilutes the cloud and thereby increases its thickness. This entrainment is stronger when the overlying inversion is weaker, so to explore this we estimate fad implied by our retrievals and bin this by estimated inversion strength (EIS; Wood and Bretherton, 2006). We apply Eq. (4), assuming that the OCO-2 and MODIS LWP are equal, then rearrange to obtain

(9)fadHOCO-2HMODIS.

The retrievals are split by τ and then the median fad in each EIS bin is calculated. EIS bins are <0C, then in 2 C increments up to 16 C and finally >16C. The results in Fig. 7a show a general tendency that OCO-2 implies increasingly subadiabatic conditions for weaker inversions, and the change from the prior to the posterior is shown in Fig. 7b.

For optically thinner clouds, the posterior state is consistent with physical expectations, and the retrieval makes substantial changes from the prior. Meanwhile, it does not make substantial changes for optically thicker clouds, although the prior itself shows the expected fad(EIS) relationship. This is due to differences between re, M and the assumed re,h=12µm used to derive our prior thickness, where MODIS re, M correlates with EIS.

We take the EIS dependence of inferred fad in Fig. 7 as evidence that our retrieval is updating our retrieved cloud thicknesses in a physically consistent way and is providing information beyond that obtained from an adiabatic prior. While we argue that this suggests additional value from our retrieval, there remain substantial uncertainties and potential biases, due to the lack of available true validation data as described in Sect. 2.1. Our first concern is the Ptop bias, as both the Ptop and ΔPc retrievals respond to photon path length, and as such a bias in one may result in biases in the other.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f08

Figure 8OCO-2 minus CALIPSO Ptop statistics for Quality_flag =0 cases, subset for aerosol layer above cloud (N1.5×106), aerosol layer below cloud (N0.5×106) or no aerosol layer detected (N6.8×106) by CALIPSO's 05kmALay. Legend reports median [14th, 18th percentiles]. (a) Clouds with posterior τ<5. (b) Clouds with posterior τ≥5.

Download

5.3 Investigation of Ptop bias

The bias in Ptop is concerning given the tight constraint provided by CALIPSO. Identifying likely causes of the bias is a priority for interpreting the data and for improving future retrievals. As changes in both Ptop and ΔPc change photon path length, it is also possible that biases in Ptop could cause counteracting biases in ΔPc. Factors that could influence the photon path length include (1) aerosol layers within the field of view, (2) a non-uniform cloud field and (3) differences in the extinction profile between the real clouds and the vertically homogeneous plane-parallel clouds used in the radiative transfer. We investigate each of these possibilities here. Further factors that we do not investigate include (i) errors in spectroscopy that affect simulated photon path lengths, (ii) improper instrument calibration or unaccounted for drifts in this calibration. We note that OCO2CLD-LIDAR-AUX used the most up-to-date ABSCO tables that were available at the time of processing and that future product versions (including an OCO-2-only retrieval under development) will use the latest calibrated spectra available.

5.3.1 Aerosol layers

We use the collocated CALIPSO 05kmALay product to identify potential aerosol layers in the OCO-2 field of view (Omar et al., 2009; Vaughan et al., 2009). This product uses multiple lidar shots averaged along-track to help identify optically thin layers that would not be reliably detected by a single shot. This product provides estimates of layer optical depth at 532 and 1064 nm as well as layer location. Here the results are separated according to whether the aerosol layer is detected above the 01kmCLay cloud or below it. Detection below the cloud is possible when there is a broken cloud scene, such that the 1 km product returns a cloud within the OCO-2 field of view but the 5 km product detects aerosol elsewhere.

Aerosol is ubiquitous in Earth's atmosphere and particularly thin layers are not detected by CALIPSO, even with extensive averaging. However, the OCO-2 radiances should only be weakly affected if a layer is thin enough to avoid detection by CALIOP.

The results are in Fig. 8 and are split by cloud optical depth above or below 5. While aerosol layers above the cloud do result in larger biases, the median shifts by 2.2 hPa for optically thin clouds and 0.6 hPa in optically thick clouds, both of which are less than half of the total Ptop bias. For optically thin clouds, above-cloud aerosol notably increases the number of strongly biased cases, shifting the 14th percentile from −20.8 to −42.8 hPa. This shift fits with aerosol layers above the cloud shortening photon path lengths and is inconsistent with a dominant role for increased surface reflection in scenes with a low value of retrieved cloud τ, since surface reflections would increase photon path length and therefore retrieved Ptop. Overall, we conclude that the presence of aerosol only has a small effect on the median retrieval, and there is no evidence that it is the dominant cause of the Ptop bias relative to CALIPSO.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f09

Figure 9Statistics of Quality_flag =0 cloud cases split into deciles based on the standard deviation of continuum A-band radiances in neighbouring footprints divided by the footprint's continuum. The points are the bin medians, and the bars cover the 14th–86th percentiles. (a) OCO-2 posterior minus prior τ, (b) OCO-2 minus CALIPSO Ptop, (c) OCO-2 posterior minus prior ΔPc, (d) OCO-2 minus collocated MODIS τ and (e) collocated MODIS re. The horizontal line in (e) is at re,h=12µm to indicate the OCO2CLD-LIDAR-AUX assumed value.

Download

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f10

Figure 10Retrieval properties for 10 orbits when assumed re, h and prior ΔPc are changed. (a) OCO-2 minus CALIPSO Ptop difference for default re,h=12µm compared with 6 and 18 µm, (b) ΔPc difference for changed re, h, (c) ΔPc retrieved for changed re, (d) Ptop difference for default ΔPc prior, and for when this is scaled by 0.5 or 2.0, (e) ΔPc for the same and (f) retrieved ΔPc for the same.

Download

5.3.2 Horizontal spatial variability

To quantify cloud spatial variability we take the standard deviation of the A-band continuum radiance in all neighbouring OCO-2 footprints and divide this by the retrieval footprint's continuum mean radiance as described in Richardson et al. (2017). This is not a direct estimate of the within-footprint variability but is likely positively correlated with it. Furthermore, footprint-to-footprint variability will also indicate where larger collocation errors are likely. Cloud motion between the OCO-2 and CALIPSO overpass times or georeferencing errors will also be larger when this parameter is higher.

In Fig. 7 we show evaluations of the retrieval (τ, Ptop, ΔPc) properties split by deciles in the radiance spatial variability. Only results in which the Quality_flag =0 retrievals are shown. For decile 1, the most horizontally homogeneous cloud fields, posterior τ and ΔPc are both reduced relative to the prior. These have opposing effects on the within-cloud photon path length. The median reduction in the extinction coefficient used in the lowest decile of retrieved clouds is 1 %, implying a minor change in within-cloud path between the prior and posterior states. However, they experience the largest changes in Ptop, implying that the spectra support shorter mean photon path lengths than those implied by the prior and that the retrieval is adjusting Ptop rather than within-cloud path length to match the spectra. Given the precision and reliability of CALIPSO, this points to another biasing factor.

Two conclusions can be reached from this result: (1) it is unlikely that cloud heterogeneity contributes to the overall positive bias in the retrievals, and (2) there are most likely compensating errors related to three-dimensional radiative transfer causing a reduction in bias as heterogeneity increases. The results so far imply that the OCO-2 spectra are consistent with a reduced photon path length relative to the a-priori cloud state used in the radiative transfer and that the OCO2CLD-LIDAR-AUX retrieval is accounting for this by shifting the cloud tops upward. The collocated MODIS properties shown in Fig. 9d and e also change with the spatial homogeneity parameters, with a larger τ and re, h in the OCO-2 retrievals than reported by MODIS, which would be the case if retrieval biases were being driven by re, h. Next we investigate whether changes in the re, h or prior ΔPc used in the radiative transfer affect the posterior Ptop.

5.3.3 Assumed cloud structure, prior ΔPc and re, h

To test the effect of the assumed re, h and prior ΔPc we select 10 orbits which had a large number of Quality_flag = 0 footprints and rerun the retrieval four times: once each with re,h=6µm and re,h=18µm and once each with ΔPc, prior scaled by 0.5 and 2.0. This results in N=64 572 Quality_flag =0 retrievals in each case, whose statistics are compared in Fig. 10. This subsample has a particularly large median Ptop difference relative to CALIPSO of −10 hPa, and changes of ±50 % in re, h only have a minor effect of ±1 hPa in the median retrieved Ptop, consistent with the values from Richardson and Stephens (2018). However, the change in prior ΔPc has a substantial effect; scaling by a factor of 0.5 almost eliminates the median bias, although at the expense of increased spread and the appearance of increased bimodality. Scaling by a factor of 2.0 increases the Ptop bias.

With regards to ΔPc, for very large prior values the retrieval generally attempts to reduce the posterior value. This is promising, as in the ×2.0 prior thickness case, the values are unrealistically large for an average case, and the retrieval is bringing them closer to reality. Despite the reductions, the posterior cloud thicknesses are unrealistically large for the ×2.0 case and unrealistically small for the ×0.5 case. Below we discuss how this may mean the retrieval is obtaining an equivalent optical ΔPc for a vertically homogeneous cloud when the observed scene is of a vertically non-uniform cloud. In the default thickness case the 14 %–86 % range in posterior minus prior ΔPc is [−5, 1] hPa; i.e. the inclusion of OCO-2 spectral information results in a thinning of the retrieved cloud, as in the unrealistically large case. When the prior thickness is halved, the difference between prior and posterior ΔPc is visually far less skewed with a range [−2, 3].

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f11

Figure 11Distributions of retrieved cloud properties over the full OCO2CLD-LIDAR-AUX dataset, split by Quality_flag =0 (QC =0 in legend) or Quality_flag >0. (a) Cloud optical depth. (b) Cloud top pressure. (c) Cloud pressure thickness.

Download

We propose that the sensitivity in retrieved properties to changing re, h and prior ΔPc is representative of their sensitivity in general terms to the scattering phase function and the vertical profile of extinction coefficient β(z) within the cloud.

The β(z) structure is more heavily weighted towards the top of the cloud in a subadiabatic cloud model, for a given τ, H and LWP (see Sect. S2, Fig. S1). This means that photons that enter a subadiabatic cloud will, on average, tend to travel shorter distances before exiting the top of the cloud than an equivalent homogenous cloud, and therefore the associated spectrum should have brighter absorption band channels. We propose that there is therefore a vertically homogeneous cloud bias introduced into the retrieval that likely manifests through reductions in retrieved Ptop and that this likely plays a substantial role in the 4–5 hPa bias in retrieved Ptop. Further modifications to the radiative transfer interface would be required to investigate this, so it is a target of future research.

This result differs from previous work such as Brenguier et al. (2000) because the derivations looked at typical retrieval channels in which atmospheric absorption was negligible over within-cloud distances. Future work will investigate whether a scaled vertically homogeneous cloud model may be used to approximate a subadiabatic cloud or whether the radiative transfer must directly include non-uniform extinction profiles.

6 Retrieval statistics and maps
Back to toptop

In Fig. 11 the full histograms of the retrieved cloud properties are shown and split by Quality_flag. Generally, the highest quality data cover clouds with a median optical thickness near 6 and a 14 %–86 % range of 2–15, while poorer quality retrievals have higher optical depths. Cloud optical depth increases poleward of the subtropics, coinciding with higher SZA and also with a higher prevalence of mixed-phase clouds, which may be misidentified and result in high equivalent liquid optical depths. The best quality data also tend to be associated with clouds that are lower in the atmosphere and have a medium pressure thickness of 25 hPa (i.e. H near 250 m).

The full period mean retrieved properties are mapped in Fig. 12 from 60 S to 60 N on a 4× 4 latitude–longitude grid, along with the extinction coefficient βext,h=τ/ΔPc. This is the βext, h for the retrieved vertically homogeneous clouds, and its interpretation is discussed below. This figure shows the lack of coverage in the central Pacific, where OCO-2 consistently measures in glint-only mode to optimize for its XCO2 retrieval. Its current mode of operation includes more ocean-dominated orbits committed to glint-only, but due to the importance of Alaska and Europe for the carbon cycle, nadir measurements of the stratocumulus decks off the coasts of Peru, Namibia, California and Australia continue.

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f12

Figure 12Mean retrieved properties over full OCO2CLD-LIDAR-AUX record on a 4× 4 latitude–longitude grid; only Quality_flag =0 retrievals are included. (a) Cloud optical depth. (b) Homogeneous cloud extinction coefficient βext,h=τ/ΔPc. (c) Cloud top pressure. (d) Cloud pressure thickness. (e) Logarithm of retrieval count.

Download

https://www.atmos-meas-tech.net/12/1717/2019/amt-12-1717-2019-f13

Figure 13Changes in retrieved properties as posterior minus prior, for Quality_flag =0 retrievals, mean value in each 4× 4 latitude–longitude grid cell.

Download

The well known geographic structures of cloud properties are visible, with coastal stratocumulus and increases in optical depth towards 60 S and 60 N. This is unsurprising given the use of the CALIPSO prior and the general agreement with MODIS.

Changes relative to the prior state are mapped in Fig. 13. Figure 13d shows the change in cloud pressure thickness from the prior, with expected patterns of relatively thinner clouds in the stratocumulus regimes, switching to thickening from the trade cumulus to cumulus regimes. For an adiabatic cloud model, Ndτ/H-5, so these results indicate a tendency for higher droplet number densities in stratocumulus regions relative to convective regions, in agreement with estimates from field measurements and theoretical expectations. This is reflected by how, in general, the βext, h posterior is higher than the prior in the marine stratocumulus decks. The shift in Ptop relative to the CALIPSO prior, which we (Sect. 5.3.3) linked to βext(z) differences between vertically homogeneous and adiabatic profiles, is larger and more negative in the stratocumulus regions too. This fits our proposal and may mean that changes in ΔPc and βext relative to the prior are similarly underestimated. Nevertheless, the stratocumulus regions are clearly visible and show changes consistent with our theoretical understanding, so we propose that this is the first detection of internal cloud structure information from hyperspectral A-band retrievals.

7 Discussion and conclusions
Back to toptop

This paper introduced and described the OCO2CLD-LIDAR-AUX product in which CALIPSO's lidar provides a tight prior constraint on Ptop, and an optimal estimation method then exploits OCO-2's hyperspectral A-band reflectance measurements to attempt a retrieval of cloud geometric thickness in addition to τ and Ptop. Output is provided to match the standards of the CloudSat Data Processing Center, and the product will be downloadable there as part of the CloudSat data release 5. Collocation with CloudSat allows direct multi-sensor investigation of these cloudy scenes, but the product also provides the full OCO-2 swath data. OCO-2 switches between nadir and glint view orbits, and only those in which OCO-2 is in nadir are processed.

The product provides great potential to explore the thickness of marine stratocumulus clouds on a large scale and the consistency of those observations with commonly assumed cloud vertical structures used in passive solar reflectance cloud retrievals. This will greatly enhance the very limited targeted airborne campaigns whose sampling is limited. Other retrievals exist but with their own potential uncertainties: MODIS relies strongly on an assumed cloud structure, while CALIPSO estimates are dominated by the cloud top. Hyperspectral A-band retrievals are based on photon path length and as such provide a physically independent method of obtaining thickness information.

Retrieval of optical depth showed good agreement with MODIS, but cloud top pressure showed a small negative bias that was strongest in the most uniform clouds that tend to occur in the subadiabatic regions. This likely leads to biases in the retrieved within-cloud path and therefore in inferred H, but through investigation of potential contributing factors we were able to rule out strong contributions from the constant assumed re, h or the presence of aerosol layers detected by CALIPSO.

Rather, we propose that the vertical extinction structure of the cloud is important, since the bias in Ptop scales with the prior ΔPc. Nevertheless, the small discrepancies relative to MODIS optical depth (Fig. 4), the tendency to retrieve more subadiabatic clouds under weaker inversions, at least for optically thinner clouds (Fig. 7), and the increased extinction coefficient in the marine stratocumulus regions (Fig. 13) suggest that the OCO-2 spectra add useful information. This information is obtained despite sub-selecting 75 out of the 853 functioning A-band channels based on a theoretical information content analysis. This reduces typical orbit processing time from >30 to 1 h. A future version is under development using the OCO-2 A-band preprocessor code in which variable re, h and integrated optical estimation and forward modelling have been implemented. If successful, a future version of this data and/or an OCO-2-only retrieval will be provided. This OCO2CLD-LIDAR-AUX release uses Version 7 OCO-2 L1bSc spectra, whereas subsequent versions corrected some calibration errors associated with instrumental ice build-up, which may introduce time-dependent instrumental errors that affect the retrieval.

We provide new information on marine stratocumulus clouds and identify a potential bias related to the cloud structure. Future work will determine whether a bias correction is possible and whether an equivalent vertically homogeneous extinction may be used to represent such clouds. While the retrieval is not directly sensitive to re, h, a retrieval of re, h using OCO-2's CO2 bands may be necessary in relating this equivalent vertically homogeneous structure to real-world cloud properties. This is a result of the within-cloud photon path information coming from molecular extinction and therefore being excluded from the results reported in past studies of cloud structure and radiative transfer in which the extinction was dominated by clouds. Any other attempts to obtain within-cloud properties using extinction-derived within-cloud paths should also consider the importance of the cloud's vertical extinction structure.

We conclude that there is evidence that OCO-2's cloudy scene footprints, which are screened and otherwise unused in the main OCO-2 products, contain useful cloud information for future investigations of marine boundary layer cloud properties. This potential is not limited to OCO-2 but includes operational or planned missions with similar A-band spectrometer specifications such as GeoCarb (Moore et al., 2018).

Data availability
Back to toptop
Data availability. 

The MOD06_L2 (Platnick et al., 2015) is available from the MODIS cloud product site at https://modis-atmosphere.gsfc.nasa.gov/products/cloud (last access: 10 March 2019), and we use the version collocated with MODIS from Taylor et al. (2016), which also describes the CALIPSO data. The OCO2CLD-LIDAR-AUX dataset will be available from the CloudSat Data Processing Center at http://www.cloudsat.cira.colostate.edu/ (last access: 10 March 2019).

Supplement
Back to toptop
Supplement. 

The supplement related to this article is available online at: https://doi.org/10.5194/amt-12-1717-2019-supplement.

Author contributions
Back to toptop
Author contributions. 

MR developed the overall retrieval code, performed the main analysis and wrote the paper. JL developed the optimal estimation code and helped with its integration. HQC provided collocation with CloudSat. JM provided the interface for cloudy radiative transfer simulations in the OCO-2 forward model. MDL assisted with product and analysis design. GLS proposed and directed the research. All authors contributed to planning and writing of the paper.

Competing interests
Back to toptop
Competing interests. 

The authors declare that they have no conflict of interest.

Acknowledgements
Back to toptop
Acknowledgements. 

This research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, under a contract with the National Aeronautics and Space Administration. Extra thanks go to Annmarie Eldering, Mike Gunson, David Crisp, Tommy Taylor and Chris O'Dell for helpful discussions, support and aid with OCO-2 data.

Edited by: Alexander Kokhanovsky
Reviewed by: three anonymous referees

References
Back to toptop

Bennartz, R.: Global assessment of marine boundary layer cloud droplet number concentration from satellite, J. Geophys. Res., 112, D02201, https://doi.org/10.1029/2006JD007547, 2007. 

Betts, A. K.: Mixing Line Analysis of Clouds and Cloudy Boundary Layers, J. Atmos. Sci., 42, 2751–2763, https://doi.org/10.1175/1520-0469(1985)042<2751:MLAOCA>2.0.CO;2, 1985. 

Boers, R. and Mitchell, R. M.: Absorption feedback in stratocumulus clouds Influence on cloud top albedo, Tellus A, 46, 229–241, https://doi.org/10.3402/tellusa.v46i3.15476, 1994. 

Boesch, H., Brown, L., Castano, R., Christi, M., Connor, B., Crisp, D., Eldering, A., Fisher, B., Frankenberg, C., Gunson, M., Granat, R., McDuffie, J., Miller, C., Natraj, V., O'Brien, D., O'Dell, C., Osterman, G., Oyafuso, F., Payne, V., Polonsky, I., Smyth, M., Spurr, R., Thompson, D., and Toon, G.: Orbiting Carbon Observatory (OCO)-2 Level 2 Full Physics Algorithm Theoretical Basis Document, Pasadena, CA, available at: https://docserver.gesdisc.eosdis.nasa.gov/public/project/OCO/OCO2_L2_ATBD.V8.pdf (last access: 10 March 2019), 2017. 

Bony, S. and Dufresne, J.-L.: Marine boundary layer clouds at the heart of tropical cloud feedback uncertainties in climate models, Geophys. Res. Lett., 32, L20806, https://doi.org/10.1029/2005GL023851, 2005. 

Brenguier, J., Pawlowska, H., Schüller, L., Preusker, R., Fischer, J., and Fouquart, Y.: Radiative Properties of Boundary Layer Clouds: Droplet Effective Radius versus Number Concentration, J. Atmos. Sci., 57, 803–821, https://doi.org/10.1175/1520-0469(2000)057<0803:RPOBLC>2.0.CO;2, 2000. 

Chambers, L. H., Wielicki, B. A., and Loeb, N. G.: Shortwave Flux from Satellite-Measured Radiance: A Theoretical Study over Marine Boundary Layer Clouds, J. Appl. Meteorol., 40, 2144–2161, https://doi.org/10.1175/1520-0450(2001)040<2144:SFFSMR>2.0.CO;2, 2001. 

Cox, C. and Munk, W.: Statistics of the sea surface derived from sun glitter, J. Mar. Res., 13, 198–227, 1954. 

Crisp, D.: Measuring atmospheric carbon dioxide from space with the Orbiting Carbon Observatory-2 (OCO-2), Proc. SPIE 9607, Earth Observing Systems XX, 960702 https://doi.org/10.1117/12.2187291, 2015. 

Crisp, D., Atlas, R., Breon, F.-M., Brown, L., Burrows, J., Ciais, P., Connor, B., Doney, S., Fung, I., Jacob, D., Miller, C., O'Brien, D., Pawson, S., Randerson, J., Rayner, P., Salawitch, R., Sander, S., Sen, B., Stephens, G., Tans, P., Toon, G., Wennberg, P., Wofsy, S., Yung, Y., Kuang, Z., Chudasama, B., Sprague, G., Weiss, B., Pollock, R., Kenyon, D., and Schroll, S.: The Orbiting Carbon Observatory (OCO) mission, Adv. Space Res., 34, 700–709, https://doi.org/10.1016/j.asr.2003.08.062, 2004. 

Crisp, D., Pollock, H. R., Rosenberg, R., Chapsky, L., Lee, R. A. M., Oyafuso, F. A., Frankenberg, C., O'Dell, C. W., Bruegge, C. J., Doran, G. B., Eldering, A., Fisher, B. M., Fu, D., Gunson, M. R., Mandrake, L., Osterman, G. B., Schwandner, F. M., Sun, K., Taylor, T. E., Wennberg, P. O., and Wunch, D.: The on-orbit performance of the Orbiting Carbon Observatory-2 (OCO-2) instrument and its radiometrically calibrated products, Atmos. Meas. Tech., 10, 59–81, https://doi.org/10.5194/amt-10-59-2017, 2017. 

Davis, A. B., Merlin, G., Cornet, C., Labonnote, L. C., Riédi, J., Ferlay, N., Dubuisson, P., Min, Q., Yang, Y., and Marshak, A.: Cloud information content in EPIC/DSCOVR's oxygen A- and B-band channels: An optimal estimation approach, J. Quant. Spectrosc. Ra., 216, 6–16, https://doi.org/10.1016/j.jqsrt.2018.05.007, 2018. 

Dong, X., Ackerman, T. P., Clothiaux, E. E., Pilewskie, P., and Han, Y.: Microphysical and radiative properties of boundary layer stratiform clouds deduced from ground-based measurements, J. Geophys. Res.-Atmos., 102, 23829–23843, https://doi.org/10.1029/97JD02119, 1997. 

Dong, X., Mace, G. G., Minnis, P., Smith, W. L., Poellot, M., Marchand, R. T., and Rapp, A. D.: Comparison of Stratus Cloud Properties Deduced from Surface, GOES, and Aircraft Data during the March 2000 ARM Cloud IOP, J. Atmos. Sci., 59, 3265–3284, https://doi.org/10.1175/1520-0469(2002)059<3265:COSCPD>2.0.CO;2, 2002. 

Drouin, B. J., Benner, D. C., Brown, L. R., Cich, M. J., Crawford, T. J., Devi, V. M., Guillaume, A., Hodges, J. T., Mlawer, E. J., Robichaud, D. J., Oyafuso, F., Payne, V. H., Sung, K., Wishnow, E. H., and Yu, S.: Multispectrum analysis of the oxygen A-band, J. Quant. Spectrosc. Ra., 186, 118–138, https://doi.org/10.1016/j.jqsrt.2016.03.037, 2016. 

Eldering, A., O'Dell, C. W., Wennberg, P. O., Crisp, D., Gunson, M. R., Viatte, C., Avis, C., Braverman, A., Castano, R., Chang, A., Chapsky, L., Cheng, C., Connor, B., Dang, L., Doran, G., Fisher, B., Frankenberg, C., Fu, D., Granat, R., Hobbs, J., Lee, R. A. M., Mandrake, L., McDuffie, J., Miller, C. E., Myers, V., Natraj, V., O'Brien, D., Osterman, G. B., Oyafuso, F., Payne, V. H., Pollock, H. R., Polonsky, I., Roehl, C. M., Rosenberg, R., Schwandner, F., Smyth, M., Tang, V., Taylor, T. E., To, C., Wunch, D., and Yoshimizu, J.: The Orbiting Carbon Observatory-2: first 18 months of science data products, Atmos. Meas. Tech., 10, 549–563, https://doi.org/10.5194/amt-10-549-2017, 2017. 

Fischer, J. and Grassl, H.: Detection of Cloud-Top Height from Backscattered Radiances within the Oxygen A Band. Part 1: Theoretical Study, J. Appl. Meteorol., 30, 1245–1259, https://doi.org/10.1175/1520-0450(1991)030<1245:DOCTHF>2.0.CO;2, 1991. 

Grosvenor, D. P. and Wood, R.: The effect of solar zenith angle on MODIS cloud optical and microphysical retrievals within marine liquid water clouds, Atmos. Chem. Phys., 14, 7291–7321, https://doi.org/10.5194/acp-14-7291-2014, 2014. 

Grosvenor, D. P., Sourdeval, O., Zuidema, P., Ackerman, A., Alexandrov, M. D., Bennartz, R., Boers, R., Cairns, B., Chiu, J. C., Christensen, M., Deneke, H., Diamond, M., Feingold, G., Fridlind, A., Hünerbein, A., Knist, C., Kollias, P., Marshak, A., McCoy, D., Merk, D., Painemal, D., Rausch, J., Rosenfeld, D., Russchenberg, H., Seifert, P., Sinclair, K., Stier, P., van Diedenhoven, B., Wendisch, M., Werner, F., Wood, R., Zhang, Z., and Quaas, J.: Remote Sensing of Droplet Number Concentration in Warm Clouds: A Review of the Current State of Knowledge and Perspectives, Rev. Geophys., 56, 409–453, https://doi.org/10.1029/2017RG000593, 2018. 

Hanel, R. A.: Determination of cloud altitude from a satellite, J. Geophys. Res., 66, 1300–1300, https://doi.org/10.1029/JZ066i004p01300, 1961. 

Heidinger, A. K. and Stephens, G. L.: Molecular Line Absorption in a Scattering Atmosphere. Part II: Application to Remote Sensing in the O2 A band, J. Atmos. Sci., 57, 1615–1634, https://doi.org/10.1175/1520-0469(2000)057<1615:MLAIAS>2.0.CO;2, 2000. 

Jones, A., Roberts, D. L., and Slingo, A.: A climate model study of indirect radiative forcing by anthropogenic sulphate aerosols, Nature, 370, 450–453, https://doi.org/10.1038/370450a0, 1994. 

Latham, J., Rasch, P., Chen, C.-C., Kettles, L., Gadian, A., Gettelman, A., Morrison, H., Bower, K., and Choularton, T.: Global temperature stabilization via controlled albedo enhancement of low-level maritime clouds, Philos. T. Roy. Soc. A, 366, 3969–3987, https://doi.org/10.1098/rsta.2008.0137, 2008. 

L'Ecuyer, T. S. and Jiang, J. H.: Touring the atmosphere aboard the A-Train, Phys. Today, 63, 36–41, https://doi.org/10.1063/1.3463626, 2010. 

Li, S. and Min, Q.: Diagnosis of multilayer clouds using photon path length distributions, J. Geophys. Res., 115, D20202, https://doi.org/10.1029/2009JD013774, 2010. 

Liang, L., Di Girolamo, L., and Sun, W.: Bias in MODIS cloud drop effective radius for oceanic water clouds as deduced from optical thickness variability across scattering angles, J. Geophys. Res.-Atmos., 120, 7661–7681, https://doi.org/10.1002/2015JD023256, 2015. 

Lohmann, U. and Feichter, J.: Global indirect aerosol effects: a review, Atmos. Chem. Phys., 5, 715–737, https://doi.org/10.5194/acp-5-715-2005, 2005. 

Mariage, V., Pelon, J., Blouzon, F., Victori, S., Geyskens, N., Amarouche, N., Drezen, C., Guillot, A., Calzas, M., Garracio, M., Wegmuller, N., Sennéchael, N., and Provost, C.: IAOOS microlidar-on-buoy development and first atmospheric observations obtained during 2014 and 2015 arctic drifts, Opt. Express, 25, 73–84, https://doi.org/10.1364/OE.25.000A73, 2017. 

Martin, G. M., Johnson, D. W., and Spice, A.: The Measurement and Parameterization of Effective Radius of Droplets in Warm Stratocumulus Clouds, J. Atmos. Sci., 51, 1823–1842, https://doi.org/10.1175/1520-0469(1994)051<1823:TMAPOE>2.0.CO;2, 1994. 

Meinig, C., Lawrence-Slavas, N., Jenkins, R., and Tabisola, H. M.: The use of Saildrones to examine spring conditions in the Bering Sea: Vehicle specification and mission performance, in: OCEANS 2015 – MTS/IEEE Washington, pp. 1–6, IEEE, 2015. 

Merlin, G., Riedi, J., Labonnote, L. C., Cornet, C., Davis, A. B., Dubuisson, P., Desmons, M., Ferlay, N., and Parol, F.: Cloud information content analysis of multi-angular measurements in the oxygen A-band: application to 3MI and MSPI, Atmos. Meas. Tech., 9, 4977–4995, https://doi.org/10.5194/amt-9-4977-2016, 2016. 

Min, Q. and Harrison, L. C.: Retrieval of Atmospheric Optical Depth Profiles from Downward-Looking High-Resolution O2 A-Band Measurements: Optically Thin Conditions, J. Atmos. Sci., 61, 2469–2477, https://doi.org/10.1175/1520-0469(2004)061<2469:ROAODP>2.0.CO;2, 2004. 

Min, Q.-L., Harrison, L. C., Kiedron, P., Berndt, J., and Joseph, E.: A high-resolution oxygen A-band and water vapor band spectrometer, J. Geophys. Res., 109, D02202, https://doi.org/10.1029/2003JD003540, 2004. 

Moore, N., Crowell, S., Rayner, P., Kumer, J., O'Dell, C., O'Brien, D., Utembe, S., Polonsky, I., Schimel, D., and Lemen, J.: The Potential of the Geostationary Carbon Cycle Observatory (GeoCarb) to Provide Multi-scale Constraints on the Carbon Cycle in the Americas, Front. Environ. Sci., 6, 109, https://doi.org/10.3389/fenvs.2018.00109, 2018. 

Munro, R., Lang, R., Klaes, D., Poli, G., Retscher, C., Lindstrot, R., Huckle, R., Lacan, A., Grzegorski, M., Holdak, A., Kokhanovsky, A., Livschitz, J., and Eisinger, M.: The GOME-2 instrument on the Metop series of satellites: instrument design, calibration, and level 1 data processing – an overview, Atmos. Meas. Tech., 9, 1279–1301, https://doi.org/10.5194/amt-9-1279-2016, 2016. 

Nakajima, T. and King, M. D.: Determination of the Optical Thickness and Effective Particle Radius of Clouds from Reflected Solar Radiation Measurements. Part I: Theory, J. Atmos. Sci., 47, 1878–1893, https://doi.org/10.1175/1520-0469(1990)047<1878:DOTOTA>2.0.CO;2, 1990. 

Nakajima, T. Y., Suzuki, K., and Stephens, G. L.: Droplet Growth in Warm Water Clouds Observed by the A-Train. Part I: Sensitivity Analysis of the MODIS-Derived Cloud Droplet Sizes, J. Atmos. Sci., 67, 1884–1896, https://doi.org/10.1175/2009JAS3280.1, 2010. 

Natraj, V. and Spurr, R. J. D.: A fast linearized pseudo-spherical two orders of scattering model to account for polarization in vertically inhomogeneous scattering–absorbing media, J. Quant. Spectrosc. Ra., 107, 263–293, https://doi.org/10.1016/j.jqsrt.2007.02.011, 2007. 

O'Brien, D. M. and Mitchell, R. M.: Error Estimates for Retrieval of Cloud-Top Pressure Using Absorption in the A Band of Oxygen, J. Appl. Meteorol., 31, 1179–1192, https://doi.org/10.1175/1520-0450(1992)031<1179:EEFROC>2.0.CO;2, 1992. 

Omar, A. H., Winker, D. M., Vaughan, M. A., Hu, Y., Trepte, C. R., Ferrare, R. A., Lee, K.-P., Hostetler, C. A., Kittaka, C., Rogers, R. R., Kuehn, R. E., and Liu, Z.: The CALIPSO Automated Aerosol Classification and Lidar Ratio Selection Algorithm, J. Atmos. Ocean. Tech., 26, 1994–2014, https://doi.org/10.1175/2009JTECHA1231.1, 2009. 

Painemal, D. and Zuidema, P.: Assessment of MODIS cloud effective radius and optical thickness retrievals over the Southeast Pacific with VOCALS-REx in situ measurements, J. Geophys. Res.-Atmos., 116, D24206, https://doi.org/10.1029/2011JD016155, 2011. 

Painemal, D., Chiu, J.-Y. C., Minnis, P., Yost, C., Zhou, X., Cadeddu, M., Eloranta, E., Lewis, E. R., Ferrare, R., and Kollias, P.: Aerosol and cloud microphysics covariability in the northeast Pacific boundary layer estimated with ship-based and satellite remote sensing observations, J. Geophys. Res.-Atmos., 122, 2403–2418, https://doi.org/10.1002/2016JD025771, 2017. 

Pawlowska, H. and Brenguier, J.-L.: Microphysical properties of stratocumulus clouds during ACE-2, Tellus B, 52, 868–887, https://doi.org/10.1034/j.1600-0889.2000.00076.x, 2000. 

Platnick, S.: Vertical photon transport in cloud remote sensing problems, J. Geophys. Res.-Atmos., 105, 22919–22935, https://doi.org/10.1029/2000JD900333, 2000. 

Platnick, S., Ackerman, S., King, M., et al.: MODIS atmosphere L2 cloud product (06_L2), https://doi.org/10.5067/MODIS/MYD06_L2.006, 2015. 

Raes, F., Bates, T., McGovern, F., and Van Liedekerke, M.: The 2nd Aerosol Characterization Experiment (ACE-2): general overview and main results, Tellus B, 52, 111–125, https://doi.org/10.1034/j.1600-0889.2000.00124.x, 2000. 

Richardson, M. and Stephens, G. L.: Information content of OCO-2 oxygen A-band channels for retrieving marine liquid cloud properties, Atmos. Meas. Tech., 11, 1515–1528, https://doi.org/10.5194/amt-11-1515-2018, 2018. 

Richardson, M., McDuffie, J., Stephens, G. L., Cronk, H. Q., and Taylor, T. E.: The OCO-2 oxygen A-band response to liquid marine cloud properties from CALIPSO and MODIS, J. Geophys. Res.-Atmos., 122, 8255–8275, https://doi.org/10.1002/2017JD026561, 2017. 

Rodgers, C. D.: Inverse Methods for Atmospheric Sounding Theory and Practice, World Scientific, Singapore, 2000. 

Rossow, W. B. and Schiffer, R. A.: ISCCP Cloud Data Products, B. Am. Meteorol. Soc., 72, 2–20, https://doi.org/10.1175/1520-0477(1991)072<0002:ICDP>2.0.CO;2, 1991. 

Schuessler, O., Loyola Rodriguez, D. G., Doicu, A., and Spurr, R.: Information Content in the Oxygen A-Band for the Retrieval of Macrophysical Cloud Parameters, IEEE T. Geosci. Remote, 52, 3246–3255, https://doi.org/10.1109/TGRS.2013.2271986, 2014. 

Spurr, R. J. D.: VLIDORT: A linearized pseudo-spherical vector discrete ordinate radiative transfer code for forward model and retrieval studies in multilayer multiple scattering media, J. Quant. Spectrosc. Ra., 102, 316–342, https://doi.org/10.1016/j.jqsrt.2006.05.005, 2006. 

Stephens, G. and Heidinger, A.: Molecular Line Absorption in a Scattering Atmosphere. Part I: Theory, J. Atmos. Sci., 57, 1599–1614, https://doi.org/10.1175/1520-0469(2000)057<1599:MLAIAS>2.0.CO;2, 2000. 

Szczodrak, M., Austin, P. H., and Krummel, P. B.: Variability of Optical Depth and Effective Radius in Marine Stratocumulus Clouds, J. Atmos. Sci., 58, 2912–2926, https://doi.org/10.1175/1520-0469(2001)058<2912:VOODAE>2.0.CO;2, 2001. 

Taylor, T. E., O'Dell, C. W., Frankenberg, C., Partain, P. T., Cronk, H. Q., Savtchenko, A., Nelson, R. R., Rosenthal, E. J., Chang, A. Y., Fisher, B., Osterman, G. B., Pollock, R. H., Crisp, D., Eldering, A., and Gunson, M. R.: Orbiting Carbon Observatory-2 (OCO-2) cloud screening algorithms: validation against collocated MODIS and CALIOP data, Atmos. Meas. Tech., 9, 973–989, https://doi.org/10.5194/amt-9-973-2016, 2016. 

Várnai, T. and Marshak, A.: Observations of Three-Dimensional Radiative Effects that Influence MODIS Cloud Optical Thickness Retrievals, J. Atmos. Sci., 59, 1607–1618, https://doi.org/10.1175/1520-0469(2002)059<1607:OOTDRE>2.0.CO;2, 2002. 

Vaughan, M. A., Powell, K. A., Winker, D. M., Hostetler, C. A., Kuehn, R. E., Hunt, W. H., Getzewich, B. J., Young, S. A., Liu, Z., and McGill, M. J.: Fully Automated Detection of Cloud and Aerosol Layers in the CALIPSO Lidar Measurements, J. Atmos. Ocean. Tech., 26, 2034–2050, https://doi.org/10.1175/2009JTECHA1228.1, 2009. 

Wood, R.: Drizzle in Stratiform Boundary Layer Clouds. Part I: Vertical and Horizontal Structure, J. Atmos. Sci., 62, 3011–3033, https://doi.org/10.1175/JAS3529.1, 2005.  

Wood, R.: Stratocumulus Clouds, Mon. Weather Rev., 140, 2373–2423, https://doi.org/10.1175/MWR-D-11-00121.1, 2012. 

Wood, R. and Bretherton, C. S.: On the Relationship between Stratiform Low Cloud Cover and Lower-Tropospheric Stability, J. Climate, 19, 6425–6432, https://doi.org/10.1175/JCLI3988.1, 2006. 

Wood, R., Mechoso, C. R., Bretherton, C. S., Weller, R. A., Huebert, B., Straneo, F., Albrecht, B. A., Coe, H., Allen, G., Vaughan, G., Daum, P., Fairall, C., Chand, D., Gallardo Klenner, L., Garreaud, R., Grados, C., Covert, D. S., Bates, T. S., Krejci, R., Russell, L. M., de Szoeke, S., Brewer, A., Yuter, S. E., Springston, S. R., Chaigneau, A., Toniazzo, T., Minnis, P., Palikonda, R., Abel, S. J., Brown, W. O. J., Williams, S., Fochesatto, J., Brioude, J., and Bower, K. N.: The VAMOS Ocean-Cloud-Atmosphere-Land Study Regional Experiment (VOCALS-REx): goals, platforms, and field operations, Atmos. Chem. Phys., 11, 627–654, https://doi.org/10.5194/acp-11-627-2011, 2011. 

Yamamoto, G. and Wark, D. Q.: Discussion of the letter by Hanel, R. A., “Determination of cloud altitude from a satellite”, J. Geophys. Res., 66, 3596–3596, https://doi.org/10.1029/JZ066i010p03596, 1961. 

Yang, Y., Marshak, A., Mao, J., Lyapustin, A., and Herman, J.: A method of retrieving cloud top height and cloud geometrical thickness with oxygen A and B bands for the Deep Space Climate Observatory (DSCOVR) mission: Radiative transfer simulations, J. Quant. Spectrosc. Ra., 122, 141–149, https://doi.org/10.1016/j.jqsrt.2012.09.017, 2013. 

Zeng, S., Riedi, J., Trepte, C. R., Winker, D. M., and Hu, Y.-X.: Study of global cloud droplet number concentration with A-Train satellites, Atmos. Chem. Phys., 14, 7125–7134, https://doi.org/10.5194/acp-14-7125-2014, 2014. 

Zuidema, P., Leon, D., Pazmany, A., and Cadeddu, M.: Aircraft millimeter-wave passive sensing of cloud liquid water and water vapor during VOCALS-REx, Atmos. Chem. Phys., 12, 355–369, https://doi.org/10.5194/acp-12-355-2012, 2012. 

Zuidema, P., Redemann, J., Haywood, J., Wood, R., Piketh, S., Hipondoka, M., and Formenti, P.: Smoke and Clouds above the Southeast Atlantic: Upcoming Field Campaigns Probe Absorbing Aerosol's Impact on Climate, B. Am. Meteorol. Soc., 97, 1131–1135, https://doi.org/10.1175/BAMS-D-15-00082.1, 2016. 

Publications Copernicus
Download
Short summary
We retrieve cloud properties, including geometric thickness, by combining hyperspectral Orbiting Carbon Observatory-2 (OCO-2) A-band measurements with CALIPSO lidar. This uses cloudy scene data that are not used in OCO-2's main mission, which is aimed at clear-sky atmospheric CO2 abundance. This is the first retrieval using such hyperspectral information and promises to provide a unique constraint on the properties of low liquid clouds over the ocean.
We retrieve cloud properties, including geometric thickness, by combining hyperspectral Orbiting...
Citation